Q&A Forum
I finally figured it out. computer was showing it as com port 4. I switched setting to port 7
I guess something else was wanting port 4??????
@osi I just checked that and cannot reproduce it. Is it reproducible on your end? If so, send me a mail on jostein@yourdyno.com and let's continue the discussion there, unless others have the same issue too.
Hi folks!
YourDyno software 3.3.61 (beta) was released today.
Changes:
- Something many of you have been waiting for: You can now have as many tabs as you want with completely configurable result graphs and tables, with different channels visible, different X-axis / master channels, different location of the channels. The setup is stored of course. There are also templates for creating new tabs for results, brake analysis, torque analysis, etc.
- The sorting of the columns in the results table is now stored in settings
- A new hotkey for Brake off and a hotkey for Save and Restart
- Live results table On or Off is now stored in settings
- Better window location saving in settings
- Digital on/off channels enabled on Standard v4
- Bug fixes:
- Weather station now works below 0C (32F) on Standard v5, requires firmware update to latest (Ultimate was already ok)
- Digital on/off channels had some spikes which are now fixed (Standard v5/Ultimate), requires firmware update to latest
- Fixed a bug that would appear in special cases when using Advanced PID settings
The Standard v5 and Ultimate have new firmware available, but it is NOT a mandatory update.
Enjoy! As always, any issues let me know.
Hi,
After upgrading to the latest version i have weird numbers doing a braked pull. Inertia is ok,but in braked mode,i see much lower values. Brake sensor is calibrated. For example run starts at 2000rpm steady,i see on live gauge 150Nm on the wheel,but after the pull the graph shows 100Nm.I see the result pop up window well before the retardation phase is done.
What setting did i miss? Dyno was ok with old sw version.
Thank you!
I have the same problem, last cars are giving very low numbers
Hi,
After upgrading to the latest version i have weird numbers doing a braked pull. Inertia is ok,but in braked mode,i see much lower values. Brake sensor is calibrated. For example run starts at 2000rpm steady,i see on live gauge 150Nm on the wheel,but after the pull the graph shows 100Nm.I see the result pop up window well before the retardation phase is done.
What setting did i miss? Dyno was ok with old sw version.
Thank you!
Problem solved thanks to Jostein! you are a legend!
Thank YOU
@xtcund install Ultraviewer and give me a call at +47 4840 1279
Hi Jostein, i have a big problem. I upgraded my dyno pc and installed latest SW version, non beta. It is saying that i must update firmare. I update online but i get the "CYRET_ERR_ROW" error, and if i try to manually update the firmare, your page doesnt let me download the Firmware downloader program (404 page not found). The main problema I have is that i get no RPM. Yourdyno says it is connected, i get all weather just fine, but not RPM. with old PC everything was working fine yesterday. Can you help please? its urgent
Hello Jostein, thanks for a lot of updates and new features!
I have found a bug, when I add a new gauge, I cannot resize it.
Thanks!
Jostein,
I work with Benjamin (benVielmi).
What we need is what is described here https://yourdyno.com/community/postid/6089/ and in the following posts.
Currently, the software is mainly oriented "make a pull from X rpm to Y rpm". But is not oriented "engine maping"
We need something either in a sequencer or in the manual mode, where we first set any RPM working point, wait stability, adjust air/fuel and ignition timing in the ECU, and then record data in the table by pressing any sort of button. At the end, the software trace a power curve from these points. This will allow us to go up and down the rpm range to map an ecu.
Angelo
Folks,
A tiny update for those who need it, version 3.3.59.
It fixes the Speed and Distance channels that were broken in the previous version.
Cheers,
Jostein
@benvielmi, please email me at jostein@yourdyno.com with a detailed description of what you are trying to do
This requires us to process the file manually wich can be long whereas with a switch to validate the data would be quick and would allow us to have a curve imediatly after the power test.
@benvielmi All the data is in the .csv file. It can be read into Excel for example.
You can also look at the data in the Results Table. There you can set Time as the Master channel and select the resolution you want, then copy to Excel.