Q&A Forum
Awesome stuff, i love this system so much, fast becoming one of the best dyno systems Worldwide now
Awesome stuff, i love this system so much, fast becoming one of the best dyno systems Worldwide now
Folks,
YourDyno software version 3.3.81 (beta) was released today.
Changes:
- A number of improvements to the gauge layout functionality
- Save/Load console (gauge layout and setup)
- Select a number of gauges and modify all selected gauges at once in terms of gauge type, size, position, range, colors, alarm, etc
- Align gauges horizontally, vertically, distribute position evenly etc.
- Undo gauge setup changes
- Hotkeys for the Run/Gauge window now work also if the Main window is active. Previously the Run/Gauge window had to be active for the hotkeys to work
- Zero calibrate button for Aux gauges
- Graphs ends are now trimmed to max RPM. This is nice if you stop the run before reaching the end RPM
- Improvement to the PID algorithm when brake was at 100% when starting the run
See https://youtu.be/RZeEIqw5EYg
As always, any issues let me know!
Cheers
Folks,
YourDyno software version 3.3.82 was released today.
Changes since 3.3.81:
- Ability to use a physical button to start/stop runs. See Options->Hotkeys. Two modes are supported
- Click to start and click to stop
- Hold button for the duration of the run, where run is started when the button is pressed and stopped when the button is released
- PTH200 plugin (weather station for YourDyno v4 hardware) was fixed
- Zero calibration of Aux channels now works for all channels (previously only aux channel 1
A physical button can be connected it to an unused RPM input or other Digital input. The button should be connected between Signal and 0V, such that pressing the button shorts Signal to 0V (creating a "0"). When not pressing the button, the signal will be "1" due to the internal pullup.
Any data channel can be used to to start and stop runs, it does not need to be a button.
Enjoy!
Hi,
YourDyno 3.3.83 was released with just a very minor fix
- Fix of the KMTronic plugin introduced in 3.3.82
Hi,
Another very small release, YourDyno version 3.3.84. It addresses an issue one person reported on YourDyno not starting up.
I have also issues with start the programm after update to version 3.3.84.
Yes, uninstall and install 3.3.81 or earlier.
Hi folks,
YourDyno version 3.3.85 is out, fixing the issues where YourDyno would not start up.
Cheers,
Jostein
Hey folks,
YourDyno version 3.3.88 (beta) was released today. Here are the changes:
- Proper revamp of the ScanTool OBD2 plugin. Now it is much faster (important!) and much easier to use. You can add and remove channels on the fly, it remembers all settings and can automatically connect and configure the channels when you start YourDyno. Check it out!
- Added two brake modes: Brake % vs Speed and Speed vs Time
- New Speed and Distance plugin. Now you can enter the diameter of the rollers (instead of the circumference) and for hub dynos you enter the wheel dimensions in the usual 285/40R20 style
- A fix of the Brake sweep with target sweep rate in RPM. Earlier it followed a fixed sweep rate, now it adjusts the brake vs the actual sweep rate (like it was intended)
- Cleanup of the Engine power calculation options window. The functionality is the same as before, but easier to understand
- Added CAN bus dbc files (configuration files) for MaxxECU and Spartan 3 WideBand
- A few other cleanups here and there
Enjoy!
@admin Any chance you have checked the MAP reading?
[Plugin] ScanTool – Page 12 – Plugins discussions, requests and sharing – YourDyno.com Forum
@michalis-antoniadis, yes it now interrogates the ECU and shows all available channels. MAP included!
Hey folks,
YourDyno version 3.3.88 (beta) was released today. Here are the changes:
- Proper revamp of the ScanTool OBD2 plugin. Now it is much faster (important!) and much easier to use. You can add and remove channels on the fly, it remembers all settings and can automatically connect and configure the channels when you start YourDyno. Check it out!
- Added two brake modes: Brake % vs Speed and Speed vs Time
- New Speed and Distance plugin. Now you can enter the diameter of the rollers (instead of the circumference) and for hub dynos you enter the wheel dimensions in the usual 285/40R20 style
- A fix of the Brake sweep with target sweep rate in RPM. Earlier it followed a fixed sweep rate, now it adjusts the brake vs the actual sweep rate (like it was intended)
- Cleanup of the Engine power calculation options window. The functionality is the same as before, but easier to understand
- Added CAN bus dbc files (configuration files) for MaxxECU and Spartan 3 WideBand
- A few other cleanups here and there
Enjoy!
The embedded link doesn't work, looks to be missing part of the link address.
click here to download YourDynoInstaller_3.3.88