Notifications
Clear all

[Sticky] Latest software version

Page 20 / 26
(@tutuur)
Enthousiast

Haven’t saved, or checked which run it was exactly. Going to use the dyno tomorrow so will see if it happens again.

 

in short, sometimes it doesn’t add the retardation data. Think it only happens when using stored retardation data.

 

Then when I apply a bit of smoothing (ctrl+selection) to a part of the graph, it then suddenly adds it

ReplyQuote
Posted : 10/04/2020 5:13 pm
(@aslot)
Member
Posted by: @admin

Tuners,

Minor update, version 3.2.74:

  • Higher RPM update rate for slow spinning rollers
  • Load Control brake mode was made smoother when transitioning from stabilization period to sweep

Cheers!

I have a 2WD HUB dyno and I can´t get RPM1 to work in 3.2.74 or 3.2.75. Only RPM2 works and the engine RPM is not correct... If I change back to version 3.2.59 RPM1 and RPM2 both works and engine RPM is correct.

Is it possible to add RPM1 and RPM2 for viewing in the graph window? I can only select brake1 and 2. (In 4WD version it should also be possible to view 3 and 4)

 

ReplyQuote
Posted : 21/04/2020 7:59 pm
(@admin)
Member Admin

@aslot, check Advanced Gear ratio setup. You may accidentally have turned on the Primary driven wheels option. This option is used when you have a 4WD roller setup and want only one set of wheels to calculate the engine RPM (i.e. for cars that are primarily front of rear drive, 4WD "light")

ReplyQuote
Topic starter Posted : 21/04/2020 9:40 pm
(@admin)
Member Admin

And yes, the Brake and Gear ratio plugin makes all Roller/Hub RPMs available to both log and show as gauges. You may need to download the newest version. 

ReplyQuote
Topic starter Posted : 21/04/2020 9:43 pm
(@aslot)
Member
Posted by: @admin

@aslot, check Advanced Gear ratio setup. You may accidentally have turned on the Primary driven wheels option. This option is used when you have a 4WD roller setup and want only one set of wheels to calculate the engine RPM (i.e. for cars that are primarily front of rear drive, 4WD "light")

The primary driven wheels option is off.

 

ReplyQuote
Posted : 22/04/2020 6:29 am
(@admin)
Member Admin

@aslot, I have tested this again now on v3.2.75, and it works correctly with all combinations I tested. So maybe I misunderstand you? 

When you say to get RPM1 to work, what do you mean exactly? If you enable the Roller1 RPM gauge, what does it show?

ReplyQuote
Topic starter Posted : 23/04/2020 9:17 pm
(@aslot)
Member

@admin, Roller1 RPM gauge shows 0RPM all the time, Roller2 RPM gauge shows the correct RPM. The total RPM(Engine RPM gauge) shows around half the real engine RPM.

The sensors are working and the gear ratio is correct, if I switch back to 3.2.59 I have RPM reading on RPM1 and RPM2 gauge and the correct Engine RPM.

ReplyQuote
Posted : 24/04/2020 6:28 am
(@aslot)
Member

I have now done some more testing.

At first start(system and PC-boot) I have RPM1 reading, after around 30s with spinning hubs the reading stops and only shows 0rpm.

If I switch the RPM1 and RPM2 connectors at the box I still only have RPM2 reading.

If I disconnect and connect the USB to the box I get RPM1 reading for around 30s again same as at first start.

I have tried to change all the filter settings but nothing works.

ReplyQuote
Posted : 25/04/2020 7:39 pm
(@andrew)
Member

@aslot  Hello,For what its worth I too am having issues with my RPM1 disappearing after a short time. I have only one RPM input, a GT101 sensor (engine dyno). I too have to do more testing but I do have a good RPM signal at the Your Dyno plug when operating correctly and also after the tacho stops. I had no RPM issues prior to this. I too updated to the latest version before this happened. All other gauges keep working without fault when the RPM stops. It does appear to be a software or box issue.

 

ReplyQuote
Posted : 26/04/2020 3:08 am
(@admin)
Member Admin

Guys, I have kept it running now for hours, I am not able to reproduce it. Can you send a raw log file with the issue to jostein@yourdyno.com please? Record when both hubs/rollers are spinning or at least when RPM1 is spinning. @aslot it would be good if you could capture the moment it stops reading RPM1. 

ReplyQuote
Topic starter Posted : 26/04/2020 2:51 pm
(@aslot)
Member

@admin, I have created a good log file now.

Attached .jpeg here and I am sending the raw on e-mail.

ReplyQuote
Posted : 26/04/2020 4:57 pm
(@admin)
Member Admin

Guys,

There was a bug in the latest firmware 1.24 which would make RPM1 hang up in some special situations, as was reported here (thanks!). 

Please upgrade to Software version 3.2.76, then click Upgrade firmware. 

Happy tuning!

ReplyQuote
Topic starter Posted : 29/04/2020 8:06 pm
(@powertuning)
Member Customer

Hello. Latest firmware will work with old software 3.2.59 ?

Regards

ReplyQuote
Posted : 29/04/2020 8:12 pm
(@admin)
Member Admin

Hello, yes that will work. 

ReplyQuote
Topic starter Posted : 29/04/2020 9:10 pm
(@andrew)
Member

@admin

Thanks for looking into this, I will do my best to test this today with the changes you've suggested.

ReplyQuote
Posted : 29/04/2020 9:14 pm
Page 20 / 26
Share:
Select your currency
EUR Euro
USD United States (US) dollar