Q&A Forum
Walter, the AFR bug; you mean when you log it is ok, but when you save the file and open it, it shows the lambda values in retardation too?
correct!
Hi.
Are there any plans for doing a live torque graph ? like the mainline dyno ?
Would be nice for finding MBT.
Yes, there is a plan for a live torque graph (or any parameter). You will be able to right-click on the gauge and choose Analog, Digital or Graph. First I am working on the ability to move curves around on different axis and graphs.
Tuners,
YourDyno 3.2.35 was released today. It contains a single fix:
- Previously if you rebooted your PC with YourDyno connected, then you would get the message "YourDyno not responding correctly, please disconnect and connect". This is now fixed. You can reboot without this (minor) annoyance.
You need to upgrade the firmware, it can be done with the press of the "Upgrade to latest firmware" button in options.
Cheers
Tuners,
YourDyno 3.2.35 was released today. It contains a single fix:
- Previously if you rebooted your PC with YourDyno connected, then you would get the message "YourDyno not responding correctly, please disconnect and connect". This is now fixed. You can reboot without this (minor) annoyance.
You need to upgrade the firmware, it can be done with the press of the "Upgrade to latest firmware" button in options.
Cheers
Ahh Good, Minor but Annoying. Another thing I have noticed that is a minor annoyance is when typing comments in the box in the main screen it does not deactivate the hotkeys so you cant use any letter keys.
Cheers
This is Actually fixed too! 👍
Not sure if I posted this earlier, but what about some safety limits for the dyno that will bring up a warning while you are dynoing. Max roller / hub speed, maybe max torque etc.
Im building a hub dyno with hydraulic pumps and the pumps have a max speed that would probably be easily exceeded if you arent paying attention. So say you can set a max pump speed of 2200rpm and it could bring a warning up as you approach it.
Not sure if I posted this earlier, but what about some safety limits for the dyno that will bring up a warning while you are dynoing. Max roller / hub speed, maybe max torque etc.
Im building a hub dyno with hydraulic pumps and the pumps have a max speed that would probably be easily exceeded if you arent paying attention. So say you can set a max pump speed of 2200rpm and it could bring a warning up as you approach it.
In the run window Push V,
Tick to show Roller/Hub RPM.
Right click that gauge in the run window and go to setup.
Set it up with the colour ranges. So green to certain RPM, Orange when aproching max RPM, Red when over.
Hi! any forecast for 4WD HUB dyno mode? i Will receive +2 load cells this week :D.
Could you please add a resettable lubber that can be tuned on on the gauges in "Run" to show the peak value?
Also some adjustable averaging on the live values setable in the gauge setup would be lovely.
Kris
Kris, good ideas.
The gauges show values today with no filtering to make them fast responding. The idea is to change this to use the filtering settings from Options with a fast on-the-fly filter algorithm (not just averaging which is slow). This anyway needs to be implemented to support live graphs as an option in addition to the digital/analog gauges.
I implementing the avarages as a ringbuffer + summ method, which is very fast and gives good result. I will share a plugin within 1-2 days which provides smooted values of the HP and Tq... this is usefull for ignition tuning.., BTW the live graphs are welcome 🙂
Does anyone have problems reading the rpm with the latest sw updates?
Does anyone have problems reading the rpm with the latest sw updates?
yes. i've had the same problem where suddenly live rpm was zero even though engine was running. restarted software and rpm worked again.
Does anyone have problems reading the rpm with the latest sw updates?
yes. i've had the same problem where suddenly live rpm was zero even though engine was running. restarted software and rpm worked again.
I have tried to restart software, re install sw and firmware, tried different setup of spike removal (0 to 5) but It doesnt work anyway.
Jostein,
could you add a tab to the rpm setup where we can select predefined rpm’s?
don’t have space to comfortably put my keyboard so would be good if I don’t need it all together.