Hi,

I am not able to replicate the issue with the changing notes (comments?) and screen going blank. Can you post the step by step way of triggering it?

For your idea on the colors, this is possible. I am currently working on a version where the user can move graphs around and then the color scheme needs to change in any case. It may be best as you say to keep black on all numbers/axis labels. The colors are anyway given by the table below. 

I removed the drum diameter from the inertia menu. It is only the MOI that matters, not the diameter. 

I've dyno'ed two customers yesterday for the first time, now playing with the graphs there are a few things i've noticed:

When changing the notes, and later on selecting extra graphs the screen goes completely blank. No option to get my graphs back again other than closing the runs and opening the csv again, quite annoying.

Secondly, the axis on the graphs color with the lines, however i'd like to set my before lines in a lighter color than the after lines. Which results in hard to read axis data. Is it possible to keep the axis data in black?

I've just upgraded my sw and noticed in the inertia dyno setup there's no drum diameter anymore, doesn't this influence the results?

Greetings tuners!

YourDyno 3.2.32 was released (beta) today. At the same time 3.2.31 is now the official release. 3.1.xx versions are depreciated.

3.2.32 gives the following:

• Ability to choose a fixed start brake percentage for Load Control brake control. The brake will ramp up to the set percentage during the initial specified wait period. This is an alternative to using the start RPM regulator
• Increased the allowable gain in Load Control to 500% (from 100%)
• Improved loading a run with retardation data recorded. The retardation data is only used to correct Engine HP and Engine Torque, so the other parameters (Lambda, etc) make the graphs hard to interpret if they are shown in the retardation phase. They are now only shown in the power run (RPM up phase). You can still see all parameters in the full run in the Results vs Time tab
• A couple of minor visual bugs fixed

Enjoy and let me know if any issues! 

Can’t wait... catch my self checking yourdyno forum more often than Facebook these days..... :p :p

That will be very useful.  Can it also be made so that we can choose what is summarised at the bottom? E.g. correction factor, env data, min or max of any sensor/plugin values.

Thanks 🙂

Thanks for the nice words, MjPower, glad you like it.

Indeed, next new feature in line is user can select where each graph will be displayed. It will be implemented in the same window where you select which graph is visible, you also select where to place the graph. 

Tried the can tool on my dyno again today. With the rpm via can, and all the others too, lambda, map, Oilpressure. And It works amazingly....

i talked with bmgjet about the posibility to have all power graphs on one side axis, and the others on the other side axis. Because you cant scale 700nm and 0.80 lambda on the same time like now...  On the other hand, 0.80 lambda, 2 bar boost and 4.5 bar oil pressure could easily be scaled together.

again, 1000 thanks to both Jostein and Brendans effort to make yourdyno the best dyno controller money can buy.... 

😊

Tuners,

Version 3.2.31 was released today. Changes:

• Retardation part of the graphs vs RPM for plugins are now removed, which makes it easier to read the graphs. This functionality was already in place for aux channels and thermocouple, but not for plugins
• Added option to use RPM[CANTool] as a source for Engine RPM. The CANTool plugin has high update rate, so this is a good option for engine RPM
• Hide the small select graph window when other windows like Run or Options are active
• Added time/date on raw log import

New version available here: https://yourdyno.com/YourDynoInstaller_3.2.31.msi

Enjoy!

Note that importing raw logs is typically used to tune noise filters or MOI, for which the points you mention are not important. You should rather save the runs as .csv instead of re-running them.

The raw data does not contain date/time. 

I will see if these points can easily be improved somewhat, not on the top of the priority list though.

 raw logs.

it's easy when you made more runs. only ''save + restart''

Posted by: powertuning

can you fix also this issues, please

2019-03-29-16_15_56-YourDyno-3.2.jpg

Are you importing raw logs? Or loading CSV file or just done runs?

Only time I see that date is with raw logs. And other glitches when opening a currupt CSV 

can you fix also this issues, please

Thank you about fixing bugs i mentioned.

About MOI per brake, i was wondering , just asking, in my case, i use both brakes , was wondering how do i would calculate MOI of each brake. 

It was only a problem if your brakes/rollers had different moi so you entered two different moi numbers. The SW used the same moi for both.

Yes i will fix those things you mention.

I hope my brakes have same MOI..  

P.S please try to fix AFR readings, if it's not hard too about WHP readings..