Q&A Forum

Notifications
Clear all

[Sticky] Latest software version

658 Posts
76 Users
168 Likes
115.5 K Views
(@admin)
Posts: 1397
Member Admin
Topic starter
 

Hi, if you upgraded from firmware 1.18 or before then that would happen if you rebooted the PC with YourDyno connected. A connect and reconnect would enable the download. That is fixed from 1.20 and onward. You can verify by pressing the upgrade button again, it will work right away. Let me know if it does not.

 

 

 
Posted : 29/06/2019 10:54 am
(@dakta)
Posts: 19
Member
 

thanks guys! I will try that 🙂

 
Posted : 29/06/2019 11:16 am
(@stvdrag225)
Posts: 15
Member Customer
 

I found the rpm pickup setup but am having a little trouble with it I have a 20 tooth wheel on my other computer I have it set on 20 and it works perfectly on the new computer on 20 it reads to high I have to set it to 30 to get it close but not sure its 100% correct 

 
Posted : 29/06/2019 12:01 pm
(@admin)
Posts: 1397
Member Admin
Topic starter
 

Always set the number of teeth to the correct value. The difference you see is from different gear ratios. There are several ways to set gear ratio, you can also copy the number from the other PC.

 
Posted : 29/06/2019 5:42 pm
(@stvdrag225)
Posts: 15
Member Customer
 

Ok I didn't realize it had a default of 1.5 to 1 my setup is 1 to 1 thanks

 
Posted : 29/06/2019 6:53 pm
Jostein reacted
(@dakta)
Posts: 19
Member
 

Hi thanks all for the assistance yesterday seems to have done the trick

 
Posted : 30/06/2019 10:49 am
(@walter)
Posts: 244
Member
 

Hi! ive been playin a bit with Print page setup. set Font doesnt work properly, tried to change size and nothing happens.. should be good to make a box that everything introduced there Will appear same in the dyno sheet.

 
Posted : 24/07/2019 1:47 pm
(@protech-racing)
Posts: 3
Member
 

Hi,  

 I have a unit about 2 months old, There is no external marking on it to determine which version  it is.   

  First question;  A note came up asking to update  firmware.  The menu ask which version it is?   What is my answer and do I need an update? 

 Next , For the roll down drag calculation. How do I get it to plot the  retardation drag?  Yo have said to right click some thing etc. Right click what ?

 Last ;for now  I have AFR on channel one . How can I get it to plot vs RPM , for full pulls? 

 Thanks a lot. MM 

 
Posted : 30/07/2019 4:40 pm
(@admin)
Posts: 1397
Member Admin
Topic starter
 

Hi,

The firmware version needs to match the software version, so yes you need to do the upgrade. Just click "Upgrade to latest firmware". The system will download the correct file automatically. All units with the blue box are version 4. 

To see the coast drag, see wheel hp and wheel torque. It is negative on the retardation phase. You can select what parameters to plot with the 'v' key. Then right-click and choose "Set scale to default" to see the full curve. 

Select the AFR channel from the list when pressing 'v'. Same shortcut for gauges.

 

 
Posted : 30/07/2019 7:19 pm
(@protech-racing)
Posts: 3
Member
 

Where is the instruction manual?  I can find nothing regarding setting this up . Not happy .

   How do I get to the window that allows the V key to do anything?   

 
Posted : 30/07/2019 7:51 pm
(@admin)
Posts: 1397
Member Admin
Topic starter
 

Protech, lots of info on dyno setup in the wiki. Other than that, there is a lot of explanations in the software itself. 

You can use the 'v' key in the main graph window and in the Run window with the gauges. 

 
Posted : 04/08/2019 10:10 pm
(@admin)
Posts: 1397
Member Admin
Topic starter
 

Greetings tuners,

YourDyno version 3.2.38 was released today. 

Changes:

  • Added functionality to set a fixed brake % after the run is done to quickly slow down the rollers/brakes. 
  • Corrected a bug which would give a slight inaccuracy in torque numbers when using two brakes and the brakes have different speed (HP was not impacted).

Cheers!

 
Posted : 04/08/2019 10:39 pm
Lasse Kofoed reacted
(@stvdrag225)
Posts: 15
Member Customer
 

Would it be possible to add a print screen like this?

 
Posted : 05/08/2019 9:57 am
(@stvdrag225)
Posts: 15
Member Customer
 

I have fahrenheit selected and its reading right but it says C

 
Posted : 05/08/2019 10:00 am
(@walter)
Posts: 244
Member
 

Good! i guess leaving it to Zero, Will not Works, does it? it's important to my dyno since we measure drivetrain losses for HPcrank calculation..

 
Posted : 05/08/2019 3:55 pm
Page 14 / 44
Share:
Select your currency