@matteozanusso, I have not experienced that myself. Check the Auto start/Stop settings, it will say which RPM it turns off at (either the End RPM, or if you have Retardation run turned on, it will stop when the RPM returns to the start RPM). 

If the problem is still there, send me a saved config file so I know your settings and I will check it out. 

hi,

with the two lastest software updates, I must stop the rum manually, even if I set it to stop automatically in the settings...

it there an additional setting that I'm missing?

thanks

Tuners,

YourDyno software version 3.2.123 is released. 

Changes:

• Ability to set Start RPM for the brake ramp-up before the run starts. It is recommended to ramp up the brake before the run starts to get a smoother start. Earlier the ramp-up would always start at 0 RPM (except for Load Control), now the ramp can start at any RPM. For example if your sweep starts at 2000 RPM, you can start the ramp up at 1000 RPM. The brake will then be 0 until the RPM reaches 1000, then it ramps gradually up towards the set Ramp % between 1000 and 2000 RPM
• Merge of the brake ramp up functionality in Load control and the generic ramp up. Earlier, Load control had its own ramp up functionality
• Fixed a bug in Load Control, where when in Manual start mode
• Hopefully(!) fixed a bug that YourDyno would very occasionally not show the curves after a run. A save and open was necessary for the curves to appear

Enjoy! As always, let me know if there are any issues. 

YourDyno version 3.2.122 is available.

• Fixed a plugin processing bug in the previous 3.2.121 version

Hi,

YourDyno version 3.2.121 is available.

• Fixed a bug in Torque readings for 4WD hub setup (when using 2 YourDyno boxes) 
• Opened up for more plugin control of the brakes by making a number of functions Public (contact me if yo are interested in making your own brake control algorithm
• Some minor cleanups

Another minor fix: 

• If no Session folder was set, Session options would not persist

You should set a Session folder, this is where all raw log files go and session specific options like gear ratio, PID parameters, etc are stored. You will get a message every time you open the Run window if you have not set a session folder. But options should anyway persist even without a Session folder set. Fixed now. 

YourDyno software version 3.2.117

Tuners, 

Here is YourDyno version 3.2.116. 

Changes:

• Fixed raw logging error (thanks @tracktoys, I noticed today as well)
• Added Hotkey for reset of graph gauges. This is useful when tuning steady state and you move to the next RPM setpoint

Cheers

Since 115 the raw logs aren't saved anymore, is that possible?

@admin much better than waiting on a fix :), Thanks for these very fast fixes and enhancements !

Indeed 😂, fixed in 3.2.115

new versions are welcome. they are not spam. For me with inertia dyno and version 3.2.114 when I open Run window Torque value is -19874NM 

Apologies for spamming you with new versions lately :-). 

Corrected a bug for Inertia dynos and a settings bug for new installations. 

Download here: YourDyno version 3.2.115. 

Hi,

YourDyno version 3.2.114 is available. 

Small bug fix:

- Removed incorrect error message when using Auto start and Auto restart

Cheers

OK my fault, there was a slight RPM drift in some runs at high rpm and it wasn't actually catch the "end RPM" value.

With a MOI of around 10 it's still a bit low probably to do it in one RUN, it calculated very low MOI (2.5 in one run, around 5 in another)
I'll try in two runs

I've tried to run the MOI measurement in one run (power sweep), but at the end it gave a warn pop-up, saying that it didn't reached the end rpm threshold, to make sure sw goes in "coast" mode, etc.

I'm pretty sure it went to coast down though, it displayed "coast", end rpm was correct and the engine did reach it in every run.

Tomorrow I'll try to do it in two runs