Q&A Forum
- I tried to find our more specification on the " Group C XJ220 Jaguar " V6 jag twin turbo engine. Mainly the torque/RPM range they operated in from light throttle to wide open throttle (WOT) ? to see how the engine and f209 worked injunction with each other!
Yes Udo your froude f0209 has a
cropped rotor ends. I'm actaully suprised that the
dyno loads up at 3000 to 3500 RPM ... I'm only going
of you ID_Tag information but the working range is
7000rpm to 16.000rpm.
Can you look in the froude f209
workshop manual ans see if
there is a torque power curve
operating graph and post a
picture of it please?
Yes He can tap into the inlet
side plus have a electric or
manual valve operating on the
oulet side to adkust sensitivity
for all different engine
torque &RPM curves but
control water inlet with
yourdyno controller.
Udo, it is interesting that it has the control valve only on the outlet, I believe it is more common to have the control valve on the inlet + a manual valve on the outlet. Some dynos have controlled valves both input and output that go opposite of each other, this gives faster response.
it is controlled only beý outlet.
The control unit ist there and I can made pictures. I have all factory paperwork for it.
I not use it often and in the past I have many problems with the controll unit. Somtimes when I switch them on it have peaks and the gauges not working. then I cange any small IC and after that it work for a while but lat time during a test the controller went off and motor rev up I was just fast enough to get throttle off before overrev. There is some defect in the controller board and I will switch to YouDyno because it is the most economy way.
Most Motor I do are V8 in the 150-800HP range so the roped rotor is not the best for my use the motors can only brake down to 3000-3500rpm
Hi Udo , Nice my first time I have seen a Froude F0209 engine brake dynamometer ID_tag , this is a high speed 750Kw (1005Bhp)@7,000/16,000 RPM engine dyno. Is it possible to get more pictures of the whole Froude F0209 engine brake dynamometer from many angles please plus the remote control panel and hydraulic pump system?
What engines have you been testing on this Froude F0209 engine brake dynamometer ? Can you share the Bhp@RPM you have been testing them at ?
On your Froude F0209 engine brake dynamometer the water is controlled on the outlet, I'm only going on the picture you posted ???? only? or both inlet and outlet ?
I have a couple of H&F G-series engine hydraulic dynamometer models, one GB4 and a G490EH and a friend of mine has a F246.
I'm converting a H&F GB4 engine hydraulic dynamometer.
I love the sound and the speed the G490EH is controlled on this youtube clip which I have already posted on this forum. Look at the tacho ! and look at the water inlet stepper motor size and gear arrangement.
https://www.youtube.com/watch?v=mG2Q48l2V7A
https://www.youtube.com/watch?v=nM6-2ROEDq0
KEY to Model Letter Designations:
R= Reversible,
D= Dual Compartment,
AV= Axial Vane (bi-directional),
GT= Gas Turbine,
FRR= Fixed Return Ring
F359: 35 = rotor size (cm),
9 = 90° crop on rotor
So I got the stepper motor and controller and will install it next days
Here a few pics from the dyno and hydraulic controller that I will replace
No it is a F209 I will take pictures later
Never seen those numbers in a h&f F series dyno. Are you sures it is a F249 maybe ?????
Welcome to the forum Udo , can you please post a picture of the ID_tag of your froude F0209 dynamometer ? Would greatly appreciate it.
Hi,
Both motors are strong. The 23ssm8442 has feedback. Feedback is not needed in a perfectly tuned setup (speed and acceleration and torque), we run without it. But can be nice, in particular if you are unsure about the setup.
ore can this be used
https://www.pollin.de/p/schrittmotor-act-23hs8442-1-80-2-phasen-2-52-v-310784
https://www.pollin.de/p/schrittmotortreiber-act-dm545-fuer-nema-23-24-schrittmotoren-24-48-v-310792
Is that what I need?
https://www.pollin.de/p/schrittmotor-closed-loop-act-23ssm8440-ec1000-1-80-2-phasen-2-4-v-310790
https://www.pollin.de/p/motortreiber-hbs57-act-fuer-closed-loop-schrittmotoren-nema-23-310791
I messure tork with an small torke adjuster theat I normal use for bearing praload.
8N/cm was need to turn with water on
Udo, Will you be able to measure the torque with the water pressure on?
I removed hydraulic actor and with water on it is very easy to turn valve by hand
No great force.
What stepper motor you recomend?