Q&A Forum

Notifications
Clear all

Gauges not updated

13 Posts
2 Users
0 Reactions
1,346 Views
(@angelo)
Posts: 31
Member
Topic starter
 

Hello,

When I configure inputs, analog and TCK, values are displayed in front of each input.

But when I start a new session and/or new run, gauges appears, but all are displaying 0.0.

I would expect values, even whe the engine is not running.

Is this normal behaviour ???

Angelo

 
Posted : 06/05/2023 4:58 pm
(@admin)
Posts: 1457
Member Admin
 

All gauges shall be live all the time. Which ones (built in aux, RPM, torque, OBD2, CAN bus,....) are updating and which are not? Do they start updating once you start the engine? 

 
Posted : 06/05/2023 11:37 pm
(@angelo)
Posts: 31
Member
Topic starter
 

Hello,

All gauges are 0.00.

Thermo-couples values are visible in the setup (option menu)

Aux inputs: no sensors connected but even the small noise present on the cables should displa anything different than 0.00

Torque value visible in the setup men

RPM is obviously at 0.0 because there is no engine on the dyno.

 

If i remember correctly, it worked once, but only after I let the starter run for few seconds at 300rpm. Then the torque value was visible and updated.

 

Software 3.3.34, but also on previous versions

Firmware 3.13

 

 

Angelo

 
Posted : 07/05/2023 5:38 pm
(@admin)
Posts: 1457
Member Admin
 

If all gauges are not updating, then there is no connection to the YourDyno box. Make sure it is connected and plugged into power. Reconnect the USB if necessary. You can check the connection in Options->Firmware update. It shall show about 110 samples /s.

 
Posted : 07/05/2023 5:51 pm
(@angelo)
Posts: 31
Member
Topic starter
 

Box IS connected, AND working. Themo-couples values are changing in the setup, I can make the stepper motor move in the setup, i can see CAN traffic.

But nothing append in the gauges. ???? ???? 

Angelo

 
Posted : 07/05/2023 8:14 pm
(@angelo)
Posts: 31
Member
Topic starter
 

Here is a screenshot:

 
Posted : 07/05/2023 8:28 pm
(@admin)
Posts: 1457
Member Admin
 

@angelo, I have never seen that before. Give me a call at +47 4840 1279 (whatsapp) and I can login and take a look. I assume you have tried to restart YourDyno. 

 
Posted : 07/05/2023 9:22 pm
(@angelo)
Posts: 31
Member
Topic starter
 

When I try to install the new software versions, Avast antivirus (free version) complain about it, verify it, send it to Avast. At the end the install can continue, but I am not totally sure everything was OK. 

Maybe the antivirus is then blocking any process. If everything is OK, how many Yourdyno processes should I view in the task manager ?

I am preparing another PC where Yourdyno software was never installed. I will install with Avast deactivated.

Angelo

 
Posted : 08/05/2023 7:11 am
(@admin)
Posts: 1457
Member Admin
 

There is one YourDyno process if you have only the main YourDyno window open, and 2 if you have the Run window open too. Just give ma a call and I can take a look at the setup. I don't think it is the antivirus as long as you are able to install.

 
Posted : 08/05/2023 7:35 am
(@angelo)
Posts: 31
Member
Topic starter
 

Hi,

Some interesting progress.

I used another PC where Yourdyno was never installed. And ......... everything Ok and run as it should ???? ???? ???? 

So I suspect a big mess with the updates I made since march. I remember I installed a version with all plugins. Then installed the next version with only 2 plugins.

I uninstalled Yourdyno, checked that directories were removed, and reinstalled YourDyno, in the hope that I find a clean install. But all my previous settings were already in the config, and still the same problem. So uninstalling doesn't remove a hidden config file, which I didn't find anywhere.

 

Angelo

 
Posted : 08/05/2023 8:06 pm
(@admin)
Posts: 1457
Member Admin
 

To delete the settings, exit YourDyno, go to the folder %localappdata%\Fonneland_Engineering_AS and delete everything there. Start YourDyno again. 

 
Posted : 08/05/2023 9:41 pm
(@angelo)
Posts: 31
Member
Topic starter
 

Hi,

Thank you for your support. Erasing the file is the solution. I can't remember when the problem occured. 

Corrupted file is available if you want to check for any bug unwanted behaviour ???? 

 

Angelo

 
Posted : 09/05/2023 7:09 am
(@admin)
Posts: 1457
Member Admin
 

Yes, thanks, send the user.config to jostein@yourdyno.com

 
Posted : 09/05/2023 7:57 am
Share:
Select your currency
EUR Euro
USD United States (US) dollar