Q&A Forum

Notifications
Clear all

[Plugin] ScanTool

174 Posts
19 Users
23 Likes
33.3 K Views
(@mach_1)
Posts: 350
Member
 

+ KTAG

 
Posted : 08/05/2019 11:02 pm
(@at2uned)
Posts: 1
Member
 

Why bmtune support dropped? Will it be added back 

 
Posted : 28/05/2019 10:35 am
(@bmgjet)
Posts: 362
Dyno Wizard
Topic starter
 

Newer versions broke support for it. Using older versions still work under ectune setting. Or use bluecan adapter which works with current version of bmtune.

 

 
Posted : 28/05/2019 11:01 am
(@rnrmotorsports)
Posts: 19
Member
 

Hi bmgjet,  Is there any way to bring in GM OBD1 data or Mega Squirt stand alone stuff?

 
Posted : 27/09/2019 9:43 pm
(@bmgjet)
Posts: 362
Dyno Wizard
Topic starter
 

GM OBD1 would be way to slow to be of any use.
Which mega squirt.
There serial protocol isnt too hard so could be added but then you would be able to tune it at the same time making it a bit pointless.
So MS with CAN bus would be a better option.

 
Posted : 28/09/2019 1:18 am
Walter reacted
(@rnrmotorsports)
Posts: 19
Member
 

MS 2 which is supposed to support CANbus networking. 

 
Posted : 28/09/2019 2:37 pm
(@skeruno)
Posts: 14
Member
 

Hi there!

 

Thanks for making this plugin! I have been trying to work with it i only have one question. Is it possible to use the scantool RPM as workable variable for the dyno functions? like with powersweeps of steady state. Currently i have not been able to do this. Yourdyno uses the roller rpm instead of the scantool RPM and i did not find any option to switch this source. Thanks in advance!

 

Kind regards,

 

Vincent

 
Posted : 02/10/2019 1:35 pm
(@admin)
Posts: 1397
Member Admin
 

Hi,

No, you need the brake RPM. Acceleration calculation needs 200 measurements per second minimum, so that will be too slow with OBD2. 

 
Posted : 02/10/2019 6:40 pm
(@rnrmotorsports)
Posts: 19
Member
 

Will this plugin work with a USB wired ELM Like this one? https://www.amazon.com/dp/B01F0GVBWY/ref=psdc_15707381_t1_B07DJZJCQ1

With using our current china ELM its very slow...like one update every second...can see definite steps in the RPM over time. 

 
Posted : 02/10/2019 10:06 pm
(@admin)
Posts: 1397
Member Admin
 

@bmgjet you know a lot about OBD2 adapters, can you recommend a good one?

 
Posted : 02/10/2019 10:13 pm
(@bmgjet)
Posts: 362
Dyno Wizard
Topic starter
 

Will be to slow.
Genuine ELMs update at 100ms, Chinese ones 250-500ms.
So even genuine ones will only give you 10 updates per second.

CAN Bus is more promising tho.
Most ECUs will do 50hz which is equal to 20ms per update.
Some will do 100hz which is 10ms per update.

Still not as fast as the rpm sensor on the dyno tho. But with CAN Bus stuff its at least fast enough to detect wheel slip where the OBD2 ELMs only really good for setting the gear ratio with.

 
Posted : 03/10/2019 12:58 am
(@tutuur)
Posts: 96
Enthousiast
 

If only I had seen this sooner. Awesome plugin!

 

I just have a few questions:

i’ve got an obd link sx, does that pass as one of the genuine ELM’s? Runs on a baudrate of 115200 iirc

 

Also any chance you’d be willing to add pids I can supply?

I’m running a Renault dedicated tuning company and running into issues on newer models which I don’t have datalogging tools for. I do however have the manufacturers sheets including enhanced diagnostic pids, would be awesome if these could be integrated!

 
Posted : 08/12/2019 10:32 am
(@tutuur)
Posts: 96
Enthousiast
 

Seeing your post above, elm’s are still too slow? Will it be possible to add support for the tactrix OP 2.0?

 
Posted : 08/12/2019 10:35 am
(@bmgjet)
Posts: 362
Dyno Wizard
Topic starter
 

When Iv got some time I need to update this since iv gotten ELMs down to 60ms responce time.
And some instructions for modding Chinese ones to 4X the speed of them. Since I also use the same ScanTool code in tuning software Im working on.

If they are standard PIDs then I can add them. Extended IDs tho is a lot more work then I want to put in.

 
Posted : 09/12/2019 12:49 am
(@tutuur)
Posts: 96
Enthousiast
 

Interesting stuff on the elm speed!

 

Standard and enhanced pids, but I have all the info you need, pid id, offset, factor, units etc. If you have these would it still be too much work? If it is I might need to look into C# myself....

 

Alternatively, if you could school me on the specific bit of code I could always do the typing work myself

 
Posted : 09/12/2019 9:16 am
Page 10 / 12
Share:
Select your currency